The 2018 Chevrolet Silverado has a Tire Pressure Monitoring System (TPMS). To adjust tire pressure, inflate tires to the correct PSI. After inflating, drive above 25 mph to reset the warning light. You can also get a dealer adjustment if needed. Always check tire pressure accuracy with a gauge.
If the Tire Pressure Monitoring System (TPMS) light illuminates, it indicates that at least one tire is under-inflated. Address this by inflating the tire to the suggested pressure. After making the adjustment, you may need to reset the TPMS. To do this, turn on the vehicle, press the TPMS reset button located under the steering column, and hold it until the TPMS light blinks three times. Then, drive for a few minutes to allow the system to recalibrate.
Maintaining the correct tire pressure is a routine task that ensures optimal performance and safety. Regularly checking your tires will extend their lifespan and improve overall driving experience.
In the next section, we will discuss how to monitor your TPMS effectively and recognize when it needs servicing. Understanding these aspects will further enhance your vehicle maintenance routine.
How Does the Tire Pressure Monitoring System (TPMS) Work in a 2018 Chevrolet Silverado?
The Tire Pressure Monitoring System (TPMS) in a 2018 Chevrolet Silverado operates by monitoring the air pressure in each tire. This system includes sensors located in each tire. These sensors measure tire pressure continuously. When a tire’s pressure falls below a certain threshold, the sensors send a signal to the vehicle’s onboard computer. This computer then activates a warning light on the dashboard. The warning light alerts the driver to low tire pressure.
The TPMS helps prevent tire underinflation, which can lead to decreased fuel efficiency and increased tire wear. Each sensor also communicates information about tire temperature. This further enhances safety as temperature changes can affect tire performance.
To reset the TPMS after adjusting tire pressure, the driver must follow a specific sequence. This usually involves turning on the ignition without starting the engine. Then, the driver needs to press the TPMS reset button, often found under the steering wheel or in the glove compartment. After releasing the button, the system will monitor the new pressure levels and adjust accordingly.
By understanding how the TPMS functions, drivers can maintain optimal tire pressure and ensure safer driving conditions in their Chevrolet Silverado.
What Are the Benefits of Using TPMS in a 2018 Chevrolet Silverado?
Using the Tire Pressure Monitoring System (TPMS) in a 2018 Chevrolet Silverado offers several benefits. These benefits include enhanced safety, improved fuel efficiency, and increased tire lifespan.
- Enhanced Safety
- Improved Fuel Efficiency
- Increased Tire Lifespan
- Cost Savings on Tire Maintenance
Enhanced Safety: The TPMS enhances safety by providing real-time tire pressure information. It alerts drivers when tire pressure drops below the recommended levels. According to the National Highway Traffic Safety Administration (NHTSA), maintaining proper tire pressure can reduce the risk of blowouts and improve vehicle handling.
Improved Fuel Efficiency: The TPMS helps improve fuel efficiency by ensuring that tires are properly inflated. Under-inflated tires create more rolling resistance, which requires more fuel to operate the vehicle. The U.S. Department of Energy states that properly inflated tires can boost fuel economy by up to 3% or more.
Increased Tire Lifespan: The TPMS increases tire lifespan by helping maintain optimal tire pressure. Maintaining the correct pressure reduces uneven wear and extends tire life. According to Tire Rack, properly inflated tires can last up to 10,000 miles longer than those that are regularly under-inflated.
Cost Savings on Tire Maintenance: The TPMS can lead to cost savings on tire maintenance. Early detection of low tire pressure reduces the need for frequent replacements. A study by the Rubber Manufacturers Association indicated that consistent tire pressure maintenance saved consumers approximately $600 million annually in extra fuel costs.
In conclusion, the TPMS in the 2018 Chevrolet Silverado contributes significantly to safety, efficiency, and maintenance cost reductions.
How Can You Accurately Check the Tire Pressure on a 2018 Chevrolet Silverado?
To accurately check the tire pressure on a 2018 Chevrolet Silverado, use a reliable tire pressure gauge to measure the pressure when the tires are cold and compare the readings to the recommended levels.
-
Tire gauge selection: Choose a digital or analog tire pressure gauge. Both types provide accurate readings. A digital gauge often offers easier reading and may include additional features, such as measurement in different units.
-
Ideal timing: Check the tire pressure when the tires are cold. Cold tires mean they have not been driven for at least three hours or have traveled less than one mile at moderate speed. Heat from driving can increase tire pressure, leading to inaccurate readings.
-
Locate the recommended pressure: Find the recommended tire pressure for your model. For the 2018 Chevrolet Silverado, this information is located on the driver’s side door jamb. It lists the ideal pressure for front and rear tires, typically around 35 PSI (pounds per square inch), depending on the specific model and tire size.
-
Measuring pressure: Remove the valve cap from the tire you wish to check. Firmly press the gauge onto the valve stem and take the reading. Ensure that the gauge is fully pressed to avoid air leaks. Compare this value to the recommended pressure.
-
Adjusting pressure: If your tire pressure is lower than recommended, add air until it reaches the desired level. If it’s higher, release some air until it matches the recommended pressure.
-
Repeat for all tires: Repeat the measurement for all four tires. Don’t forget the spare tire, if applicable, as it also requires proper inflation.
-
Resetting the TPMS: If your vehicle is equipped with a Tire Pressure Monitoring System (TPMS), and you adjust the tire pressure, you may need to reset the system. Start the engine, ensure the TPMS warning light is off, and drive the vehicle for a short distance to allow it to re-calculate the pressures.
Regularly checking tire pressure helps maintain optimal vehicle performance, improves fuel efficiency, and enhances safety on the road.
What Is the Recommended Tire Pressure for a 2018 Chevrolet Silverado?
The recommended tire pressure for a 2018 Chevrolet Silverado is typically between 35 to 40 psi (pounds per square inch). This value may vary based on the specific tire size and load requirements. Maintaining the correct pressure ensures optimal vehicle performance, safety, and fuel efficiency.
According to the National Highway Traffic Safety Administration (NHTSA), proper tire inflation is critical for safe driving and vehicle longevity. Adhering to these recommendations can prevent tire blowouts and improve fuel economy.
Correct tire pressure affects various aspects of vehicle operation. Under-inflated tires can lead to increased wear, poor handling, and reduced fuel efficiency. Over-inflation can decrease traction and increase the risk of tire damage.
The Tire Industry Association emphasizes that tires should be checked monthly and before long trips. They recommend referring to the vehicle manufacturer’s specifications to determine the correct pressure.
Factors affecting tire pressure include temperature changes, tire wear, and load. For instance, colder temperatures can cause tire pressure to drop. Excessive weight in the vehicle can also increase the need for higher pressure.
Research from the U.S. Department of Energy indicates that proper tire inflation can improve fuel efficiency by 3% to 6%. Maintaining recommended pressure can save drivers approximately 25 cents per gallon.
Improper tire pressure can cause accidents, increased fuel costs, and reduced efficiency. It is crucial for vehicle safety and environmental sustainability.
Health impacts include decreased vehicle safety, which can lead to injuries or fatalities. Environmental consequences involve increased fuel consumption and greenhouse gas emissions.
Examples of these impacts are seen in higher frequencies of tire-related accidents and increased carbon footprints from inefficiencies in fuel use.
To address these issues, regular tire pressure checks are recommended. The NHTSA advises equipping vehicles with Tire Pressure Monitoring Systems (TPMS) to alert drivers of pressure changes.
Strategies include using digital tire pressure gauges and adhering to maintenance schedules. Education on tire care can also help mitigate issues associated with improper tire pressure.
How Do You Safely Adjust the Tire Pressure on a 2018 Chevrolet Silverado?
To safely adjust the tire pressure on a 2018 Chevrolet Silverado, you should check the recommended pressure, use a tire pressure gauge, inflate or deflate the tires as necessary, and reset the Tire Pressure Monitoring System (TPMS).
First, determine the recommended tire pressure. The ideal pressure for a 2018 Chevrolet Silverado is typically found on the driver’s side door jamb or in the owner’s manual. This figure is crucial because proper tire pressure ensures optimal vehicle safety and efficiency.
Next, acquire a reliable tire pressure gauge. These gauges measure the air pressure within a tire. Digital gauges are often more accurate than analog ones. To check the tire pressure, remove the valve stem cap from one tire and press the gauge onto the valve stem. The reading should be noted for comparison against the recommended pressure.
Now, inflate or deflate the tires as needed. If the tire pressure is too low, use an air compressor to add air until it reaches the recommended level. For over-inflated tires, press the valve stem with a tool to release excess air until the correct pressure is achieved. It is important to make these adjustments when the tires are cold, as heat from driving can increase pressure readings.
Finally, reset the TPMS. If the tire pressure has been adjusted significantly, the TPMS may need to be reset to avoid warning lights. To do this, turn on the ignition without starting the engine. Press the TPMS reset button until the warning light blinks three times, indicating that the system is reset. Driving the vehicle for a short distance usually calibrates the system automatically.
Following these steps ensures the tire pressure is properly adjusted, enhancing safety, performance, and fuel efficiency. Regularly checking tire pressure, as recommended by the National Highway Traffic Safety Administration (2020), can also improve tire longevity and save on fuel costs.
What Are the Steps to Reset the TPMS After Adjusting Tire Pressure in a 2018 Chevrolet Silverado?
To reset the Tire Pressure Monitoring System (TPMS) after adjusting the tire pressure in a 2018 Chevrolet Silverado, follow these steps:
- Check and adjust tire pressure.
- Turn the ignition to the “On” position without starting the engine.
- Locate the TPMS reset button under the steering column or dash.
- Press and hold the TPMS reset button until the TPMS light blinks three times.
- Release the button and turn the ignition off.
- Start the engine and allow a few minutes for the TPMS to reset.
These steps provide a clear method for resetting the TPMS, but there are various considerations one might take into account for this process.
-
Types of TPMS:
– Direct TPMS
– Indirect TPMS -
Importance of Regular Tire Pressure Checks:
– Enhances safety
– Improves fuel efficiency -
Considerations for Tire Maintenance:
– Seasonal changes impact tire pressure.
– Frequency of tire pressure adjustments.
Transitioning from these considerations can help clarify the types of Tire Pressure Monitoring Systems and their importance in vehicle maintenance.
-
Types of TPMS:
Types of TPMS include direct and indirect monitoring systems. Direct TPMS utilizes pressure sensors in each tire to provide real-time data on tire pressure. This system alerts the driver if tire pressure drops below a predefined threshold. Indirect TPMS, on the other hand, does not use pressure sensors; instead, it estimates tire pressure by monitoring wheel rotation speed through the Antilock Braking System (ABS). The NHTSA states that vehicles with direct TPMS can provide more accurate readings compared to indirect systems. -
Importance of Regular Tire Pressure Checks:
Regular tire pressure checks play a vital role in vehicle safety and efficiency. Properly inflated tires improve handling and braking performance. According to the National Highway Traffic Safety Administration (NHTSA), under-inflated tires can lead to blowouts and accidents. Furthermore, maintaining the correct tire pressure can improve fuel efficiency by up to 3%, as confirmed by a 2005 EPA study. -
Considerations for Tire Maintenance:
Seasonal changes significantly impact tire pressure. Tires lose approximately 1 PSI (pound per square inch) for every 10°F drop in temperature. Therefore, checking tire pressure during seasonal transitions is crucial. Additionally, the frequency of tire pressure adjustments varies depending on driving conditions and tire wear. It’s advisable to inspect tire pressure at least once a month, especially before long trips, to ensure optimal performance and safety.
In summary, resetting the TPMS in a 2018 Chevrolet Silverado after adjusting tire pressure is a straightforward process that incorporates various types of systems and regular maintenance practices.
What Should You Do If the TPMS Warning Light Remains On After Adjusting Tire Pressure?
If the Tire Pressure Monitoring System (TPMS) warning light remains on after adjusting tire pressure, you should reset the system or inspect for potential issues.
- Reset the TPMS light.
- Check for faulty TPMS sensors.
- Inspect for tire damage or leaks.
- Confirm accurate tire pressure.
- Consult a professional mechanic.
To better understand these issues, let’s dive deeper into each aspect associated with the TPMS warning light.
-
Reset the TPMS Light: Resetting the TPMS light is essential after adjusting tire pressure. This process usually involves using a button on the dash or through the car’s settings. Some vehicles may require you to drive a certain distance or turn the ignition on and off in a specific sequence to reset the system. As per the manufacturer’s instructions, the reset method can vary significantly across different vehicle brands and models.
-
Check for Faulty TPMS Sensors: Faulty TPMS sensors can cause the warning light to remain illuminated. Each tire has a sensor that monitors pressure and sends signals to the vehicle’s computer. If a sensor fails, it may need to be replaced. According to the National Highway Traffic Safety Administration (NHTSA), sensor malfunctions are responsible for about 10% of TPMS warning light issues.
-
Inspect for Tire Damage or Leaks: Inspecting tires for physical damage or leaks is crucial if the TPMS light does not turn off. A puncture or sidewall damage can lead to air loss, causing the system to activate. Performing a visual inspection and using soapy water to check for hissing sounds can help detect leaks.
-
Confirm Accurate Tire Pressure: Confirming that tire pressure is actually correct is vital. Use a reliable tire gauge to check each tire’s pressure and compare it to the manufacturer-recommended levels. According to the Tire Industry Association, nearly one in four cars is driven with underinflated tires, affecting safety and fuel efficiency.
-
Consult a Professional Mechanic: If all other steps fail, consulting a professional mechanic is advisable. They can conduct a comprehensive diagnostic check. Mechanic services often include specialized tools to detect system faults that the average person might not access. A professional can provide insights on whether the issue is related to the TPMS or if it involves other vehicle systems.
How Can Regular Maintenance Help You Maintain Proper Tire Pressure in a 2018 Chevrolet Silverado?
Regular maintenance helps you maintain proper tire pressure in a 2018 Chevrolet Silverado by ensuring that your tires remain in good condition, allowing for accurate pressure readings, and preventing issues like uneven wear and reduced performance.
Regular inspections: Inspecting tires for damage, wear, and correct inflation levels helps ensure that they operate efficiently. According to the National Highway Traffic Safety Administration (NHTSA), proper tire inflation can improve fuel efficiency by up to 3.3%.
Pressure checks: Checking tire pressure frequently, ideally once a month, guarantees that they are inflated to the manufacturer’s recommended levels. The recommended pressure for the 2018 Chevrolet Silverado can typically be found on the driver’s side door jamb.
Adjustment and inflation: Regular maintenance includes adjusting tire pressure if readings are low. Under-inflated tires can lead to poor handling and increased braking distance. Research from the AAA Foundation for Traffic Safety (2020) states that 1 in 4 vehicles on the road has at least one under-inflated tire.
Alignment and rotation: Regularly rotating and aligning tires promotes even wear and helps maintain proper contact with the road. Uneven wear can cause a loss of pressure and performance. The American Automobile Association recommends rotating tires every 5,000 to 7,500 miles.
TPMS (Tire Pressure Monitoring System) functionality checks: The TPMS alerts drivers when tire pressure falls significantly below recommended levels. Regular maintenance ensures that the TPMS is functioning correctly, reducing the risk of driving on under-inflated tires. According to a study published in the Journal of Transport and Health (Mason et al., 2019), a working TPMS can reduce the incidence of tire blowouts.
In summary, regular maintenance activities such as inspections, pressure checks, adjustments, rotations, and TPMS functionality checks are vital in maintaining proper tire pressure in a 2018 Chevrolet Silverado. This practice improves safety, fuel economy, and overall vehicle performance.
Related Post: