What Battery Does An Impala Tire Pressure Sensor Take? TPMS Replacement Guide [Update On 2024]

The tire pressure sensor in an Impala uses a 3-volt lithium-ion battery. This battery is built into the sensor and cannot be replaced separately. The expected battery life is 7-10 years. For the sensor to work properly, it must be compatible and programmed with the vehicle’s Tire Pressure Monitoring System (TPMS).

To replace the TPMS sensors effectively, begin by obtaining the correct replacement sensors. It’s essential to read the manufacturer’s specifications. Once you have the new sensors, use a tire pressure gauge to check the current tire pressure before removing the tires. After safely removing the tire, detach the old sensor from the valve stem and install the new one. Reattach the tire and make sure to calibrate the new sensor with your vehicle’s onboard computer.

Following these steps ensures the TPMS functions properly. Next, we will delve into the specific procedures for recalibrating the TPMS after sensor replacement, ensuring that your Impala maintains accurate tire pressure readings and optimal safety.

Table of Contents

What Is a Tire Pressure Monitoring System (TPMS) in an Impala?

A Tire Pressure Monitoring System (TPMS) in an Impala is an electronic system that continuously monitors the tire pressure of the vehicle. It alerts the driver when tire pressure falls below a specific threshold, enhancing safety and performance.

According to the National Highway Traffic Safety Administration (NHTSA), TPMS is designed to prevent tire blowouts and improve vehicle fuel efficiency. The system plays a critical role in maintaining optimal tire conditions for safe driving.

TPMS operates through sensors located in each tire, measuring air pressure. These sensors send data to the vehicle’s onboard computer, which triggers warnings if pressure is inadequate. Regular tire pressure checks can prevent underinflation and overinflation.

The NHTSA further defines TPMS as vital for maintaining adequate tire pressure, which can enhance tire life, improve fuel economy, and reduce the risk of accidents. Properly functioning TPMS can significantly impact overall vehicle safety.

Common causes of TPMS warnings include temperature changes, punctures, or natural air loss over time. Seasonal temperature fluctuations can lead to reduced tire pressure and prompt system alerts.

Statistics from the NHTSA indicate that properly inflated tires can improve gas mileage by up to 3.3% and reduce crash risk due to tire failure. They estimate that TPMS could prevent approximately 100 lives lost and 4,600 injuries annually.

The implications of TPMS include improved road safety and environmental benefits, such as reduced carbon emissions from better fuel efficiency. A well-maintained TPMS contributes positively to public health by promoting safer driving conditions.

Impact examples include reduced vehicle accidents and a decrease in costs associated with tire repairs and replacements. A well-functioning TPMS can lead to significant long-term savings for drivers.

To address TPMS-related issues, maintaining the system through regular inspections and sensor replacements is critical. Regular tire maintenance, including checks for leaks or damage, also plays a role.

Implementing practices such as routine tire pressure checks, leveraging smartphone apps for reminders, and adhering to manufacturer guidelines can help mitigate TPMS issues effectively. These strategies can enhance vehicle safety and performance.

What Type of Battery Does an Impala Tire Pressure Sensor Use?

The Impala tire pressure sensor typically uses a CR2032 battery.

Common battery type: CR2032
Battery dimensions: 20mm diameter, 3.2mm thickness
Battery characteristics: Lithium chemistry
Alternative battery types: Occasionally, other models may use batteries such as CR2450
Lifespan: Approximately 5 to 10 years, depending on usage

The following section will provide a detailed explanation of each point regarding the battery type used in Impala tire pressure sensors.

Common Battery Type:
The common battery type for the Impala tire pressure sensor is the CR2032. This coin cell battery is widely used in various electronic devices due to its compact size and reliability. It provides a nominal voltage of 3 volts, which is standard for tire pressure monitoring systems.
Battery Dimensions:
Battery dimensions for the CR2032 measure 20mm in diameter and 3.2mm in thickness. These dimensions are essential for ensuring proper fitting within the tire pressure sensor housing. A battery that does not meet these specifications may not function correctly or fit properly.
Battery Characteristics:
The CR2032 battery employs lithium chemistry. Lithium batteries are known for their long shelf life and stable voltage output. This characteristic is crucial for tire pressure sensors, which are expected to operate reliably over extended periods without frequent replacement.
Alternative Battery Types:
Occasionally, some models of the Impala may use an alternative battery type, such as the CR2450. The CR2450 is larger, measuring 24mm in diameter and 5.0mm in thickness, providing more capacity. However, the CR2032 remains the most common type used.
Lifespan:
The lifespan of a tire pressure sensor battery typically ranges from 5 to 10 years. This duration depends on factors like driving conditions and sensor usage. Typically, a battery that lasts longer is indicative of lesser demand from the sensor.

In summary, the Impala tire pressure sensor generally relies on a CR2032 battery, known for its compact size and longevity. Understanding these specifications can help ensure proper maintenance and functionality of the tire pressure monitoring system.

How Can You Identify the TPMS Battery in an Impala?

You can identify the Tire Pressure Monitoring System (TPMS) battery in an Impala by checking the vehicle’s tire sensors, consulting the owner’s manual, and confirming the battery specifications.

Tire sensors: Each tire has a TPMS sensor that monitors tire pressure. The sensor contains a battery that typically lasts five to ten years. If the tire pressure warning light illuminates on the dashboard, it might indicate a dead or low battery in one or more sensors.
Owner’s manual: The owner’s manual for the Chevy Impala often contains specific details about the TPMS. It will inform you of the sensor location and battery type. Refer to the section on tire maintenance or TPMS for accurate information.
Battery specifications: The batteries used in TPMS sensors are usually CR2032 or similar lithium coin cell batteries. To confirm the exact type, you may need to remove the tire sensor from the wheel, which typically requires specialized tools or help from a professional.

Understanding these steps aids in efficiently managing tire pressure maintenance and ensuring that the TPMS operates correctly. Regular checks can prevent issues related to tire under-inflation or over-inflation, enhancing vehicle safety and efficiency.

What Signs Indicate That the TPMS Battery in an Impala Is Dead?

The signs that indicate the TPMS (Tire Pressure Monitoring System) battery in an Impala is dead include a malfunctioning warning light, inaccurate pressure readings, and recurring alert messages.

Malfunctioning warning light
Inaccurate pressure readings
Recurring alert messages

These signs are essential for ensuring safe driving. Understanding them is crucial for maintaining optimal tire performance.

Malfunctioning Warning Light: A malfunctioning warning light in the Impala signals potential issues with the TPMS. The light may blink or remain illuminated, indicating that the system cannot communicate with the sensors due to a dead battery.
Inaccurate Pressure Readings: Inaccurate pressure readings occur when the TPMS battery is not functioning properly. This can lead to false readings, such as showing that tire pressure is normal when it is not, jeopardizing both safety and performance.
Recurring Alert Messages: Recurring alert messages on the dashboard indicate that the TPMS may not be relaying correct data. These messages can reappear even after resetting the system, suggesting issues with battery longevity or sensor functionality.

Maintaining awareness of these signs can help drivers address potential TPMS battery failure promptly, ensuring a safe and efficient driving experience in their Impala.

How Do You Replace the TPMS Battery in an Impala?

To replace the TPMS battery in an Impala, you need to access the tire pressure monitoring system sensor, remove the old battery, and install a new one.

First, locate the TPMS sensor. It is found inside each tire, attached to the valve stem. The sensor measures tire pressure and communicates with the car’s onboard computer. Next, follow these steps:

Remove the tire: Use a jack to lift the vehicle and take off the wheel where the sensor is located. Ensure safety by securing the vehicle with jack stands.
Dismantle the tire: Deflate the tire completely. Use a tire iron to separate the tire from the rim. This step requires a tire changing machine or manual tools to break the bead.
Access the sensor: Once you remove the tire, locate the TPMS sensor mounted to the inside of the rim. You may need to unscrew or unclip it from its position.
Replace the battery: Open the sensor casing carefully to avoid damage. Remove the old battery, noting the orientation. Install a new battery, ensuring the positive (+) side faces the same direction as the old one. It is important to use a compatible battery, usually a CR2032 or similar size, depending on the model year of the Impala.
Reassemble the tire: Put the sensor back in place and ensure it is secure. Reattach the tire to the rim, ensuring it is seated properly. Inflate the tire to the recommended pressure listed on the door jamb.
Reinstall the wheel: Attach the wheel back onto the vehicle, ensuring all bolts are tightened to the manufacturer’s specifications.
Reinitialize the TPMS system: Start the vehicle and drive for a few minutes. This allows the system to recalibrate and recognize the new battery within the sensor. If the warning light remains on, consult the vehicle’s manual for additional reset procedures.

Following these steps will successfully replace the TPMS battery in an Impala, ensuring the tire pressure monitoring system functions correctly. Proper maintenance of TPMS can enhance vehicle safety and performance by providing real-time tire pressure information.

What Tools Do You Need for Replacing the TPMS Battery?

To replace the TPMS (Tire Pressure Monitoring System) battery, you need specific tools and items.

Screwdriver (flathead or Phillips)
Replacement TPMS battery
Tire pressure gauge
Torque wrench (optional for specific vehicles)
Tire iron or lug wrench
Safety goggles and gloves
Valve core tool (if applicable)

Having the right tools is essential for a successful battery replacement. When considering these tools, it’s important to understand their purpose and functionality. Each tool serves a unique role in the battery replacement process, and may vary depending on the vehicle make and model.

Screwdriver:
Using a screwdriver is necessary for removing the sensor cover. Both flathead and Phillips types may be needed, depending on the specific screws used in your vehicle.
Replacement TPMS Battery:
A replacement battery is essential as the initial battery has likely lost its charge. Check the vehicle manual for the correct type and size of the battery.
Tire Pressure Gauge:
A tire pressure gauge is vital for checking tire pressure after the battery has been replaced. Proper tire pressure is crucial for vehicle safety and performance.
Torque Wrench:
A torque wrench may be optional, but using it ensures that the wheel nuts are tightened to the manufacturer’s specifications. This tool is especially important if the car needs specific torque settings for safety.
Tire Iron or Lug Wrench:
A tire iron or lug wrench is necessary for removing the wheel. This allows access to the TPMS sensor within the tire.
Safety Goggles and Gloves:
Wearing safety goggles and gloves protects you from debris and sharp objects when working with tires and tools.
Valve Core Tool:
If your vehicle requires it, a valve core tool may be necessary for safely removing or replacing the valve core during battery replacement.

By gathering these essential tools and items, you can effectively replace your TPMS battery and ensure your vehicle remains safe and efficient on the road.

How Do You Access the TPMS Sensor for Battery Replacement?

To access the Tire Pressure Monitoring System (TPMS) sensor for battery replacement, follow these steps: locate the TPMS sensor within the tire, remove the tire from the wheel, and carefully replace the sensor’s battery.

Locate the TPMS Sensor: The TPMS sensor is typically embedded in the tire’s valve stem. It monitors the tire pressure and sends data to the vehicle’s onboard computer.
Remove the Tire: To access the TPMS sensor, you must first remove the tire from the wheel. This process usually requires:
– Lifting the vehicle with a jack.
– Removing the lug nuts using a wrench.
– Taking the tire off the wheel assembly.
Replace the Sensor’s Battery: After removing the tire, locate the TPMS sensor. To replace the battery, follow these steps:
– Unscrew the battery enclosure, which is often secured with small screws.
– Carefully detach the old battery.
– Insert a new battery of the correct type, usually a CR2032 or similar, ensuring proper polarity.
Reassemble the Tire: Once the battery is replaced, reassemble the sensor and tire.
– Reattach the tire to the wheel.
– Tighten the lug nuts, ensuring even pressure across all nuts.
Re-inflate the Tire: Inflate the tire to the recommended pressure as specified in the vehicle’s manual.
Reset the TPMS: Finally, reset the TPMS after reinstallation to clear any alerts on the dashboard and ensure proper functioning.

By following these steps, you can successfully access the TPMS sensor and replace the battery for continued tire pressure monitoring.

What Are the Best Practices for Maintaining TPMS Batteries in an Impala?

The best practices for maintaining TPMS (Tire Pressure Monitoring System) batteries in an Impala include regular inspections, proper tire maintenance, and timely battery replacements.

Regular Inspections
Proper Tire Maintenance
Timely Battery Replacements
Monitoring Tire Pressure Levels
Use of Quality Batteries

Implementing these practices ensures the optimal functioning of your vehicle’s TPMS and helps in recognizing issues early.

Regular Inspections:
Regular inspections of TPMS batteries involve checking for signs of wear, corrosion, and proper functioning. The TPMS system in the Impala is designed to alert the driver when tire pressure is low. By visually inspecting sensors and battery contacts, drivers can detect any issues that may affect system performance.
Proper Tire Maintenance:
Proper tire maintenance includes maintaining correct tire pressure and adjusting it as needed. The recommended tire pressure for an Impala is typically found on the driver’s door jamb. Consistently checking and adjusting the tire pressure helps ensure that the TPMS operates efficiently and prolongs battery life.
Timely Battery Replacements:
Timely replacements of TPMS batteries are crucial. On average, these batteries last about 5-7 years. It is recommended to replace them when replacing tires or when there is a low battery warning. Consider that tax on this maintenance could be higher if neglected, possibly leading to costly repairs.
Monitoring Tire Pressure Levels:
Monitoring tire pressure levels using the dashboard indicator helps in maintaining optimal settings. TPMS systems usually display a warning light when tire pressure deviates from the recommended range. Regularly checking this can prevent damage to the tires and enhance safety.
Use of Quality Batteries:
Using high-quality batteries specifically designed for TPMS can ensure better performance and longevity. Poor quality or incompatible batteries may fail prematurely or cause the sensor to malfunction. It’s essential to consult vehicle specifications and use batteries that meet those guidelines.

These best practices can significantly enhance the longevity and reliability of your Impala’s TPMS, ensuring safe and efficient driving.

When Should You Consider Upgrading Your TPMS Battery in an Impala?

You should consider upgrading your Tire Pressure Monitoring System (TPMS) battery in an Impala when you notice a few specific signs. First, if the TPMS warning light on your dashboard remains illuminated, it may indicate a weak battery. Second, if you experience frequent alerts regarding low tire pressure, even when the tires are properly inflated, it points toward battery issues. Third, if a tire pressure sensor becomes unresponsive or exhibits delayed readings, that may signal the need for a battery replacement.

Regular checks or changes typically occur every five to seven years, coinciding with other routine vehicle maintenance. Monitoring the performance of your TPMS sensors regularly can help you identify battery-related issues early. Additionally, if you are replacing your tires, it’s wise to check the condition of the TPMS batteries. If you encounter any of these situations, upgrading the TPMS battery is recommended to ensure optimal performance and safety in your Impala.

Related Post:

What Battery Does an Impala Tire Pressure Sensor Take? TPMS Replacement Guide