Lowering The Infiniti JX35 Spare Tire: Tips For Easy Removal And Replacement [Update On 2025]

To lower the spare tire on a 2013-2020 Infiniti JX35, open the hatch and find the lowering mechanism. Insert the T-bar at a 40-degree angle about six inches into the mechanism. If using a donut spare, ensure proper mounting. Always follow safety precautions, and have a jack kit or tire patch kit ready for assistance.

Once the tire is fully lowered, verify that it is free from any obstacles. Gently pull the spare tire toward you and detach it from the winch mechanism. Remember to inspect the spare tire for any visible damage as well. After examining the tire, it is important to reverse the process for replacement. Raise the spare tire back into its original position by turning the winch tool clockwise until it securely holds the tire.

By following these steps, you can effectively lower the Infiniti JX35 spare tire with ease. In the next section, we will discuss how to properly store the spare tire after use, ensuring it remains in good condition for future needs.

Table of Contents

How Can You Safely Lower the Infiniti JX35 Spare Tire?

To safely lower the Infiniti JX35 spare tire, follow a systematic approach that includes locating the tire, using the proper tools, and ensuring stability during the process.

Locate the spare tire compartment: The spare tire is stored under the vehicle and can be accessed from the rear of the Infiniti JX35. Ensure the car is parked on a flat, stable surface before proceeding.
Gather necessary tools: You will need a tire jack and a lug wrench. The jack typically comes with the vehicle, located in the trunk. The lug wrench is also included and is used to loosen and tighten the tire nuts.
Prepare the vehicle: Engage the parking brake to prevent the vehicle from rolling. Verify that the jack is functioning correctly before using it.
Use the jack to lower the tire: Insert the jack crank into the designated hole under the vehicle. Turn the crank to lower the spare tire to the ground. Ensure that the jack is stable and secure throughout this process.
Unscrew the spare tire: After lowering, retrieve the spare tire from its location. Use the lug wrench to remove any retaining bolts holding the tire in place.
Replace and secure the spare tire: Position the spare tire on the axle. Hand-tighten the bolts to hold the tire in place, then use the lug wrench to tighten them fully.

Following these steps helps ensure that the spare tire is safely lowered and can be utilized without risk. Always refer to the vehicle’s manual for any specific instructions or recommendations.

What Essential Tools Do You Need to Lower the Infiniti JX35 Spare Tire?

To lower the Infiniti JX35 spare tire, you need a specific set of tools and equipment.

The essential tools required are as follows:
1. Spare tire tool kit
2. Jack handle
3. Hydraulic jack
4. Lug wrench
5. Torque wrench

Having identified these tools, it is essential to understand their individual purposes and applications.

Spare Tire Tool Kit: The spare tire tool kit contains essential components needed for tire replacement. It typically includes the jack, lug wrench, and any other tools necessary for lowering the spare tire. Referencing the owner’s manual is crucial to ensure all components are included and functioning.
Jack Handle: The jack handle is a long rod used to operate the jack to lift the vehicle. It needs to be sturdy and fit securely with the jack. Quality jack handles ensure safe lifting of the vehicle, preventing accidents while changing a tire.
Hydraulic Jack: The hydraulic jack is essential for lifting the vehicle high enough to access the spare tire. This type of jack, favored for its efficiency and ease of use, can handle heavy weights. It operates by fluid pressure, making it easier to raise the vehicle compared to manual jacks.
Lug Wrench: The lug wrench is used to remove the lug nuts holding the tire in place. A cross-shaped or tire iron wrench offers better leverage, making it easier to remove tightly secured nuts. Incorrect use can strip the lug nuts, so using the proper technique is important.
Torque Wrench: The torque wrench ensures that lug nuts are tightened to the manufacturer’s specified pressure. Proper torque adds safety and prevents wheel detachment. Failure to use a torque wrench can lead to serious accidents due to improperly secured tires.

In conclusion, utilizing the right tools for lowering the Infiniti JX35 spare tire not only ensures a smooth process but also enhances safety during the procedure.

How Do You Locate the Spare Tire Release Mechanism?

To locate the spare tire release mechanism, check under the vehicle, in the trunk, or behind panels inside the vehicle. Each vehicle may have a different location for the release mechanism; therefore, consulting your owner’s manual can provide specific details.

Under the vehicle: Many vehicles have the spare tire mounted under the rear. In these cases, a release mechanism often requires using a tool to lower the tire to the ground.
In the trunk: Some models store the spare tire in the trunk or cargo area. The release mechanism might be located near the tire itself or within the trunk’s lining, often requiring a simple lever or latch to access the tire.
Behind panels: Certain vehicles may have the spare tire hidden behind paneling in the cargo area or floor. Pressing a button or using a special tool may trigger the release mechanism.

For the best guidance, always refer to the vehicle’s owner’s manual. This will provide detailed information on finding and operating the spare tire release mechanism specific to your car model.

What Techniques Facilitate the Easy Removal of the Spare Tire?

The techniques that facilitate the easy removal of the spare tire include the following.

Proper tools and equipment
Familiarize with the vehicle manual
Utilizing a tire iron
Engaging with hydraulic jacks
Assessing the vehicle’s clearance and stability

Effective removal of the spare tire requires careful consideration of these techniques.

Proper Tools and Equipment: Having the right tools makes the spare tire removal process smoother. Essential tools include a lug wrench, jack, and possibly a tire inflation kit. Using the proper size of the wrench can prevent stripping lug nuts. This is crucial, as improper tools can complicate removal.
Familiarize with the Vehicle Manual: Before attempting to remove the spare tire, it’s essential to understand your vehicle’s specifications. The vehicle manual contains crucial information about tire changing procedures and locations of the spare tire. A study by the National Highway Traffic Safety Administration (NHTSA) emphasizes the importance of drivers knowing their vehicle systems for safety and efficiency.
Utilizing a Tire Iron: The tire iron is a valuable tool for loosening lug nuts. Applying the proper technique, such as using leverage and the correct turning direction, makes loosening easier. It’s important not to exert too much force, as this may damage the lug nut. A user guide from AAA recommends using the “lefty-loosey” method.
Engaging with Hydraulic Jacks: Hydraulic jacks provide a stable way to lift the vehicle. They reduce manual effort and allow for safe tire removal. Operating a hydraulic jack correctly minimizes the risk of vehicle slip, which is crucial during tire changes.
Assessing the Vehicle’s Clearance and Stability: Before starting the removal process, check the vehicle’s stability on the ground. Ensuring that the car is on a level surface and appropriately using wheel chocks for stability can prevent accidents. The Car Care Council suggests doing this for maximum safety while working with vehicles.

Integrating these techniques can ensure a smoother and safer process when it comes to removing the spare tire.

What Precautions Should You Take When Replacing the Spare Tire?

When replacing a spare tire, it is essential to take specific precautions to ensure safety and effectiveness.

Ensure the vehicle is on a stable, flat surface.
Use wheel chocks to prevent rolling.
Activate the vehicle’s hazard lights.
Wear gloves to protect your hands.
Check the spare tire’s pressure before installation.
Use the appropriate tools, including a jack and lug wrench.
Follow the car manufacturer’s guidelines for tire replacement.
Be cautious of hot components, especially after driving.
Securely stow the flat tire after removal.
Test drive after installation to ensure proper handling.

Taking these precautions not only enhances safety but also improves the efficiency of the tire replacement process.

Stable, Flat Surface: Ensuring a vehicle is on a stable, flat surface is crucial when replacing a spare tire. A firm foundation prevents the vehicle from rolling or tipping, which can lead to injuries. According to the National Highway Traffic Safety Administration, over 300 roadside fatalities involve vehicles rolling while changing tires each year.
Wheel Chocks: Wheel chocks serve as blocks to prevent the vehicle from rolling. Placing wheel chocks behind the tires helps secure the vehicle in position. The American Automobile Association (AAA) recommends using chocks on both sides of the tires opposite to the one being changed.
Hazard Lights: Activating the vehicle’s hazard lights alerts other drivers of your presence. This is particularly important if changing a tire on a busy road. The presence of hazard lights can significantly decrease the likelihood of accidents.
Wear Gloves: Wearing gloves provides protection for your hands from dirt, grease, and sharp edges. It can also improve grip on tools and components during the tire change. A study by the American Occupational Safety and Health Administration indicates that gloves reduce injury risks while working with mechanical tasks by approximately 60%.
Spare Tire Pressure: Checking the spare tire’s pressure ensures it is safe to use. A flat spare can lead to dangerous situations. The Rubber Manufacturers Association advises that spare tires should be inflated to the pressure recommended by the vehicle manufacturer, usually found in the owner’s manual.
Appropriate Tools: Using the correct tools, like a jack and lug wrench, is essential for effective tire replacement. Improper tools can lead to mishaps. The AAA recommends carrying a complete roadside emergency kit that includes a spare tire, jack, lug wrench, and other tools.
Manufacturer Guidelines: Following manufacturer guidelines ensures that you are using correct procedures for tire replacement. These guidelines often contain specific instructions, including how to properly install the spare tire. The vehicle manual is a valuable resource for this information.
Caution with Hot Components: After driving, the tires and brake components may be hot. Caution is necessary to avoid burns. The National Safety Council highlights the importance of waiting for components to cool down before handling them.
Securely Stow Flat Tire: After removing the flat tire, secure it in the vehicle to prevent it from rolling around. Proper stowage prevents additional damage to the vehicle and maintains safety for passengers.
Test Drive: After tire replacement, a test drive ensures that the spare tire is correctly installed. A quick drive allows the driver to check for any handling issues. The Automotive Service Association advises that all replaced tires be inspected on the road promptly to confirm proper performance.

Taking these precautions when replacing a spare tire strengthens personal safety and assures a more successful replacement experience.

How Can You Prevent Common Mistakes When Lowering the Infiniti JX35 Spare Tire?

To prevent common mistakes when lowering the Infiniti JX35 spare tire, follow these essential tips: understand the correct procedure, ensure proper tools are available, and avoid interference with the locking mechanism.

Understanding the procedure is crucial. The correct steps include locating the spare tire crank, which is usually stored with the jack and tools. Next, familiarize yourself with the jack’s operation. The owner’s manual provides specific instructions to follow. Ensuring you know how to raise and lower the tire will help avoid any missteps.

Having the right tools available makes the process smoother. Check for the jack, tire wrench, and any necessary extensions. The tire wrench must fit the lug nuts properly to prevent stripping. It is also wise to have gloves to improve grip and protect hands during the process.

Avoiding interference with the locking mechanism is vital for a seamless operation. If the spare tire is locked in place, ensure you unlock it before attempting to lower it. Forcing the tire down without proper unlocking can cause damage to the mechanism.

By adhering to these tips, you can effectively lower the Infiniti JX35 spare tire while minimizing errors.

Related Post:

Lowering the Infiniti JX35 Spare Tire: Tips for Easy Removal and Replacement